How do I bridge two different amps together?

Let’s learn how do I bridge two different amps together. The most accurate or helpful solution is served by ecoustics.com.

There are ten answers to this question.

Best solution

How do you bridge two amps together to each power one sub ...

okay i have two Legacy LA-2499 Blue Steel Series 2600 Watt Mono Block MOSFET amplifiers and i need to know how to bridge them together so they each power a different ...

ecoustics.com

Other solutions

How would i bridge two amps together to power my 2 Rockford Fosgate P3s?

2 rockford Fosgate P3's both 4 ohms right now i am only powering one off of 4 gauge wire to a RS500 amp need to be able to run both of them need some help on how to do it

Answer:

you want to run two amps or 2 subs off 1 amp?? I cant figure out what you want? the12volt.com is the...

Read more

Btown03M... at Yahoo! Answers Mark as irrelevant Undo

Can i bridge two amps together to run one set of subs?

can i bridge two amps, both fosgate, one about 500 watts rms and the other about 250 watts rms, together to run one set of subs? or is that a bad idea?

Answer:

That is not doable. Best case scenario: it won't work Worst case scenario: you start a fire and fry...

Read more

razzinhe... at Yahoo! Answers Mark as irrelevant Undo

Is it possible to bridge two amps together for more power?

I have two 1800 watt kenwoods, but both of them blew. I now downgraded my system with a kenwood kac 7202 2 channel amp. I found this in the manual and was wondering if it would work with a 2 2 channel amps? Dual Mono Drive (Function of the KAC-9152D...

Answer:

An amp has to be intended for external bridging. I would be seriously surprised if you did this and...

Read more

joker at Yahoo! Answers Mark as irrelevant Undo

Answer:

yea i agree with both there ansewers dont do you'll fry em

Read more

vanisifa... at Yahoo! Answers Mark as irrelevant Undo

What happens if i bridge two amps that are not the same brand or watts?

my amp is 200 watts at bridged 4 ohms and i want to that can i bridge it with another amp that has a higher power in watts? my amp is bridgeable too . i read it on its manual.

Answer:

you are talking about strapping and it's completely different. those types of amps are specially designed...

Read more

B4DHVB4S4ZVERL33KWFYXO7MGA at Yahoo! Answers Mark as irrelevant Undo

Kicker subs L7 how to wire subs RF amps bridge?

i have two S15L7(4) DVC with 2 RFT10001BD(one for each) i just dont know if i should wire them @ 2 or 4 ohms...what would it be better? or loud? also about the amps since i can hook 2 speakers is it possible to bridge them? http://www.rockfordfosgate...

Answer:

Go with wiring them to 2 ohms. This is best because the lower the resistance the more current you can...

Read more

pina85 at Yahoo! Answers Mark as irrelevant Undo

Wheatstone bridge comparator?

ok, so a wheatstone bridge is set up as two voltage dividers consisting of two resistors each, with each divider parallel to the other. when the bridge is balanced the voltage between the two center points of the dividers should be zero. so when i connect...

Answer:

Without seeing your circuit I can't be sure that I am answering your question, but here goes. There...

Read more

Thomas Payne at Yahoo! Answers Mark as irrelevant Undo

Can I use two 2-channel amps with two dual voice coil speakers?

The speakers are 4-ohms per coil (2 ohms) and I have two amps to power them. I would bridge each amp into them and use one amp per speaker but they are only stable at 2 ohms unbridged. So could I hook one left to one voice coil and the other amp's left...

Answer:

NEVER connect two channels to one sub. The slightest difference in power can cause the coils to warp...

Read more

Daniel at Yahoo! Answers Mark as irrelevant Undo

How can I hook up my same amps to my same subs?

I have two 12 in kicker P1s and two JVC 400 watt GT series amps. I want to bridge each amp to one sub so I can get 400 watts to both subs for a total 800. There both in their own box ...show more

Answer:

How are you going to do that? You have 2 subs, you want to hook up 2 amps to each sub but you only have...

Read more

74V3HTZFH2BX5MJOPKJRW3KM2U at Yahoo! Answers Mark as irrelevant Undo

Related Q & A:

Just Added Q & A:

Find solution

For every problem there is a solution! Proved by Solucija.

  • Got an issue and looking for advice?

  • Ask Solucija to search every corner of the Web for help.

  • Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.