How do I get max power out of my amp?

Let’s learn how do I get max power out of my amp. The most accurate or helpful solution is served by Yahoo! Answers.

There are ten answers to this question.

Best solution

How can i get max power out of my amp with out frying it?

i have a hifonics bxi 606 http://www.onlinecarstereo.com/CarAudio/ProductDetail.aspx?ProductID=16363 amp and i want to get the most power out of it i can without screwing it up and ...show more

Answer:

Set the gains correctly. Your amp cannot put out more power than it's rated for -esp. being a HiFonics...

Read more

N23U6DSASTWZEEKGUFYPS6WXJQ at Yahoo! Answers Mark as irrelevant Undo

Other solutions

2-12" kicker cvx 750 rms, 1500 max, 2000.1 class d mono amp, how much power will my subs get?

They are 2 ohm subs. Does my amp know if it is powering so many ohms, or is there a setting on the amp itself to output at 2 ohm, 4ohm etc.

Answer:

Lol trenton the only amp tht gives the same rms at any load wud be the rockford fosgates CP's (constant...

Read more

Kevin Krebs at Yahoo! Answers Mark as irrelevant Undo

When you bridge an amp do you get the max power all the time?

Ex. A 1000 watt amp. 1000 watts is the maximum power when bridged. Lets say the amp is 1000W x 1 @ 4 ohms bridged. When bridged is this 1000W continuous power or just max power? Next question. What if I have two subs. Since the amp is 1000W x 1 @ 4ohms...

Answer:

RMS (abbreviation for root mean square) is a way of measuring alternating current (AC) by averaging...

Read more

SAIII at Yahoo! Answers Mark as irrelevant Undo

I have 2 12" Kicker CVX subwoofers and a Kenwood Excelon Amp. Do I need 2 of these amps to get max power?

2 12'' Kicker CVX Solobaric Subwoofers 2 Ohm/Dual Voice Coil 750W/1500W (RMS/Peak) In ported box Kenwood Excelon KAC-X522 2 Channel Amp 4 X 254 Watts RMS @ 2 Ohms Do I need two amps because I don't think the subs are hitting at max power?

Answer:

no the cvx is a good sub i have 6 but dont push them to the max the rubber gets loose its good to keep...

Read more

B.Wright at Yahoo! Answers Mark as irrelevant Undo

Answer:

It's a borderline setup even in a best case scenario. I couldn't find a lot of specifics on the amp...

Read more

wiki.answers.com Mark as irrelevant Undo

Answer:

When your engine is not running, the amp is running only off the battery, which should be 12.6 volts...

Read more

asparks0... at Yahoo! Answers Mark as irrelevant Undo

Answer:

MAX or PEAK watts is not a valid means of measuring power, always go by the RMS rating as this is a...

Read more

RTAAGZWWV7BXYHVZRNU2ESSMPI at Yahoo! Answers Mark as irrelevant Undo

Answer:

yeaaaa if it's a monoblock you cant change the resistance if you can bridge it then yes you can change...

Read more

GDQCVLBZMHKU4QSBW7AYMNUSOI at Yahoo! Answers Mark as irrelevant Undo

6" x 9" 3 way speaker with 260W max power what size amp would i need to get more out of them?

i got a 2007 pioneer head unit witch soports 4-50 watt and i just wont to get more out of my speakers

Answer:

2 channel amp would power your 6x9's, key thing is you have to match the RMS rating of of each speaker...

Read more

ryan d at Yahoo! Answers Mark as irrelevant Undo

Answer:

My advice to you would be to make sure to buy a class d mono amp that will put out something in the...

Read more

Anonymous at ChaCha Mark as irrelevant Undo

Related Q & A:

Just Added Q & A:

Find solution

For every problem there is a solution! Proved by Solucija.

  • Got an issue and looking for advice?

  • Ask Solucija to search every corner of the Web for help.

  • Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.