How do i know if i'm allergic to aluminum?

Let’s learn how do i know if i'm allergic to aluminum. The most accurate or helpful solution is served by Answerbag.com.

There are ten answers to this question.

Other solutions

Aluminum for thermite?

I have been trying to make some thermite for a while now, and I haven't had much success. I have tried using iron oxide and that didn't work. then I tried using manganese dioxide, also without success. I'm pretty sure I have the right proportions for...

Answer:

In 35+ years of demonstrating the thermite reaction, I have used fine aluminium powder to quite visible...

Read more

Cameron Atkinson at Yahoo! Answers Mark as irrelevant Undo

If i get a large chunk of aluminum who would i contact to get it forged into a block?

im looking for a strong forged aluminum block & want to know who i should contact or how i could-get a large chunk of solid melted aluminum melted & forged into a block (i want to use ...show more

Answer:

Well, in that case, you should call a local metal supplier and see what they can order you. It's likely...

Read more

5TM7ECCI6GP6OXYOFFWJPUA5WY at Yahoo! Answers Mark as irrelevant Undo

How do I join two pieces of aluminum parts?

I have two pieces of aluminum parts (like long cylinders) with elliptical cross sections (diameters 60mm and 500mm). I need to join them. Im afraid welding might mess up the surface of the parts where they join (its important for me to have them joined...

Answer:

Utilize a V-shaped holder to support the two elliptical pieces and then align and secure them. The best...

Read more

Nick R at Yahoo! Answers Mark as irrelevant Undo

How do I join two pieces of aluminum parts?

I have two pieces of aluminum parts (like long cylinders) with elliptical cross sections (diameters 60mm and 500mm). I need to join them. Im afraid welding might mess up the surface of the parts where they join (its important for me to have them joined...

Answer:

Welding is still your best solution. You can always get it welded by someone who is really skilled at...

Read more

Nick R at Yahoo! Answers Mark as irrelevant Undo

I need information on aluminum and heat transfer!?

Now, I'm doinq my Science Fair Project. Its about wether the Cookie Sheet a cookie is baked on affects how the cookie turns out... Now, I have to write somethinq about heat transfer and aluminum and parchment paper.... I know NOTHING about it.... I Need...

Answer:

Heat transfer is energy in transit as the result of a temperature difference. There are 3 mechanism...

Read more

[!!]Viviana[!!] at Yahoo! Answers Mark as irrelevant Undo

Need info on turning my 16ft aluminum boat into a sailing vessel?

i need some information on building a sail and mast for my 16ft 1957 arkansas traveler.i know it is a little odd and maybe a bit unrealistic but im going to give it my best shot. I will be mainly sailing on the St.Lawrence and Lake Ontario. ive done...

Answer:

"ell jay" is only partially right. You do need a center board or keel. But, that is NOT what...

Read more

mike l at Yahoo! Answers Mark as irrelevant Undo

Is it bad to mix computer ram made of different metals eg. gold/aluminum/copper?

you know how you get ram that's made of different things like gold/copper/aluminum whatever, is it bad to mix these? Im getting another GB of ram for my laptop, but i want to know if it matters if the new stick of ram is made from a different metal than...

Answer:

No. Its better that they are the same brand (Not material) . But no, It will still work.

Read more

Samantha at Yahoo! Answers Mark as irrelevant Undo

How to mount bow mount trolling motor on a aluminum boat?

hey im getting a free trolling motor off someone i know the only down side its a bow mount and i only have a little aluminum with no where to mount the thing. has anyone else done this or dose anyone have any ideas on how to do it

Answer:

You add a wood or metal plate for the mount. They sell some plates just for that purpose.

Read more

Jake at Yahoo! Answers Mark as irrelevant Undo

Boat throttle system for a 14 foot aluminum boat?

Just got a used 14 foot aluminum boat with a 1980 outboard 10 hp murcury engine, im putting a push/pull steering system in. I know you can buy throttles but i dont know how to connect ...show more

Answer:

Is the engine made to accept cables if not than U have issues if so needed is a control box.there is...

Read more

DINAWPO5I3ZTTQRBV73QQWOIDM at Yahoo! Answers Mark as irrelevant Undo

Related Q & A:

Just Added Q & A:

Find solution

For every problem there is a solution! Proved by Solucija.

  • Got an issue and looking for advice?

  • Ask Solucija to search every corner of the Web for help.

  • Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.