How to wire 2 dvc subs to mono amp?

Let’s learn how to wire 2 dvc subs to mono amp. The most accurate or helpful solution is served by answers.yahoo.com.

There are ten answers to this question.

Best solution

How to wire 2 DVC subs to a mono-block amp? | Yahoo Answers

I have an mtx 421d mono block amp wired to 2 mtx 4500's that are single voice-coil. I've thought about upgrading to 2 mtx 5500's with dual-voice coils, how ...

answers.yahoo.com

Other solutions

How do I wire two DVC 4 ohm subs to a mono amp that is only stable to 2 ohms?

I have two Audiobahn AW1206T DVC subs that are 4 ohms each and I want to wire them up to a Phoenix Gold R15.0:1 mono amp that is only 2 ohms stable. There are two sets of speaker terminals on the Mono amp and I am not sure how they are wired internally...

Answer:

Here's how to wire series-parallel and is the only way for 4 ohms in your case http://i81.photobucket...

Read more

sanjoses... at Yahoo! Answers Mark as irrelevant Undo

1 got 3 different amp's to choose from which is best for my 2 dvc 4ohm subs,and how do i wire it 4 more boom?

i have two 4ohm dvc PERFORMANCE TEKNIQUE sub 500 rms,and three amps to choose from but dont know wich is the best for my subs could you let me know which of them you think ill get more power from and how to wire that subs to that amp? here are the specs...

Answer:

All three of those amps are NOT enuff to power TWO of your subs. you have two subs that are 500rms EACH...

Read more

jesse m at Yahoo! Answers Mark as irrelevant Undo

How do I wire 2 DVC subs at 4 ohms ea into a 2 ohm amp?

I mostly just want some verification on something. From my understanding, if I wire two DVC subs that are 4 ohms each to 1 ohm each, then hook them up to a 600w rms x1 at 2 ohms amp, they would be putting out 300w in each amp right? Or am I misunderstanding...

Answer:

STOP!!!!! a pair of dvc 4 ohm subs can only represent a 1 or 4 ohm load. check the diagram here http...

Read more

Phil at Yahoo! Answers Mark as irrelevant Undo

How do I wire two dvc 4ohm subs to a 2 ohm stable 2 channel amp?

I have a 2000 watt 2 ohm stable 2 channel logic amp. I am trying to wire two 4 ohm dvc kicker cvrs. Is this even possible because my amp is not mono? Please help. I've gone through many pairs, I wana get it down right this time. Thanks

Answer:

this should help you i had the same question but with 2ohm subs http://akamaipix.crutchfield.com/ca...

Read more

JJ at Yahoo! Answers Mark as irrelevant Undo

How do i wire 2 dvc subs to a 4 channel amp?

i have a kicker zx650.4 amp and two 2 ohm DVC memphis m3 12" subs. how do i wire the amp and subs together? please tell me if i have bought the wrong equipment or if it isss at all possible to make it work.

Answer:

That amp will run real hot at a 2 ohm bridge, so what you need to do is wire those voice coils in "...

Read more

athlete6... at Yahoo! Answers Mark as irrelevant Undo

What is the best way to wire my 2 10" dvc 4 ohm subs to a mono block amp with 2 speaker inputs?

They are jbl 10" dvc 4 ohm subs at max 350 rms and the amp is jbl gto 7001 max 700 any help will be greatly helpful thanks

Answer:

4 ohms per voice coil for 8 ohm subs or 2 ohm per voice coil for 4 ohm subs... check with JLAudio dot...

Read more

joe at Yahoo! Answers Mark as irrelevant Undo

How do I wire my 2 JL W3v2 DVC subs (4 OHM) to my JC Power 1000.1D 2 channel amp?

Amp: 2 Channel, JC Power 1000.1D (I think its 1000Watt peak at 1 ohm, not sure at all though) Subs: 2 12'' JL Audio W3v2, 4-Ohm DVC (3oo watt rms) So, what I am asking is ...show more

Answer:

Ok I can't find any information on this amp. Who makes it? Is JC initials for the actual name? I need...

Read more

D3RA44EG24LQ4IQGSTO64NH2TA at Yahoo! Answers Mark as irrelevant Undo

Answer:

When you have 2 resistors of the same value in parallel, the total resistance is 1/2 of one ot them...

Read more

AFCMNURFDG6BEELK2GPTQGWE3M at Yahoo! Answers Mark as irrelevant Undo

How do i properly wire a monoblock amp to two dvc subs ?. if the volume is up past 15 when my car is started the amp goes into protection .?

If i listen to music when my car is not on it doesnt go into protection mode. Amp - boss r1600m Subs- audiobahn aw1251t 800 w peak

Answer:

Your amp is good for loads for 2-8 ohms. I believe your subs have two 4Ω coils each, so if you...

Read more

KJBOXAV2NP3G4WFJTVON5SXYGI at Yahoo! Answers Mark as irrelevant Undo

Related Q & A:

Just Added Q & A:

Find solution

For every problem there is a solution! Proved by Solucija.

  • Got an issue and looking for advice?

  • Ask Solucija to search every corner of the Web for help.

  • Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.