How to wire an ignition wire to my deck?

Let’s learn how to wire an ignition wire to my deck. The most accurate or helpful solution is served by ca.answers.yahoo.com.

There are ten answers to this question.

Best solution

how to wire a ignition wire to my deck? | Yahoo Answers

How do I wire my Ignition wire *red* to the ignition key switch, OR the fuse box. It shows in the decks diagram Battery, to Car fuse box (main fuse ...

ca.answers.yahoo.com

Other solutions

What is the ignition wire for in car audio deck?

okay I have a 1987 honda accord and replacing the deck with a sony xplod deck. I match all possitive and negative wiring for speakers together and 12vt battery wire hooked up. BUT ...show more

Answer:

The wiring harness should have a switched 12v wire on it..12v when key is on.. 0v when key is off..You...

Read more

4BIQ2QKUWYY3EAIDGPAV7HSBIE at Yahoo! Answers Mark as irrelevant Undo

How to install car stereo in 1984 volvo - with only constant power... no ignition power wire?

I'm trying to install a pioneer tape deck into my 1984 volvo 240 wagon. I have only 1 green wire that seems to have power. This is regardless of whether the ignition is on or not. There is no other wire with power... the others, I assume, are speaker...

Answer:

Wow-that Pioneer deck must be at least ten years old. They haven't used those wire colors in a while...

Read more

chud at Yahoo! Answers Mark as irrelevant Undo

2005 GMC sierra radio ignition wire, where is it?

i cant find where the audio ignition wire is. i popped the stock deck out and looked for it but cant find it. on a diagram i found, it said its a yellow wire but one of the speakers is also a yellow wire. there's only one there though. im confused.

Answer:

You will not find an accessory wire behind the radio, because it's done through data. You'll have to...

Read more

Daniel at Yahoo! Answers Mark as irrelevant Undo

2000 Audi A4 ignition wire have no power?

the black wire on the ignition harness does not show 12 volts when I turn the ignition to the ON position. I was wondering if there's a fuse for the ignition wire. the car does not start. there's power on the accessory wire, there are power on both the...

Answer:

The pos pwr wire running to ignition point is actually controlled by the ECM/ECU - if the acusecur coding...

Read more

jonathan at Yahoo! Answers Mark as irrelevant Undo

2000 Audi A4 ignition wire have no power?

the black wire on the ignition harness does not show 12 volts when I turn the ignition to the ON position. I was wondering if there's a fuse for the ignition wire. the car does not start. there's power on the accessory wire, there are power on both the...

Answer:

Have you checked the ignition switch itself? It could be worn out due to old age.

Read more

jonathan at Yahoo! Answers Mark as irrelevant Undo

Ok then heres another question. is the coil+ wire go to the ignition or to the fuse box then the ignition.?

I also have a big red wire that comes from the silver box into the boot where does that go? A red and black wire from the ignition to boot wheres that connecting? Then from the back of the clock i have three wires missing indicators. lights and main...

Answer:

http://search.yahoo.com/search;_ylt=Ai.6… There you go look it up yourself.

Read more

Jon-11 at Yahoo! Answers Mark as irrelevant Undo

1970 Ford F100. Did I WIRE this ignition bypass correctly?

This is an old 1970 ford pick-up. My key no longer works in the ignition so I installed a "toggle-switch/push-button" bypass system. I'm not sure I wired it correctly and hope someone can let me know if there is a problem with this method....

Answer:

Those ignitions were equipped with a ballast resistor to feed 8 volts to the coil. and 12 volt bypass...

Read more

jfcruzr at Yahoo! Answers Mark as irrelevant Undo

How to identify the ignition wire on a ford focus mk2?

I am installing DRLs (Daylight Running LEDs) on my 2005 focus lx. The original plan was to connect them to either straight to the ignition fuse or to the sidelights. After having a look and deciding that it was quite difficult to get the wires into the...

Answer:

It may be the red wire from the ignition switch. If not there are only two wires, so it will be the...

Read more

Sion at Yahoo! Answers Mark as irrelevant Undo

How do i wire up a atv ignition circuit?

hi all how do i wire up a atv ignition circuit i have the battery fat + wire feeding the starter relay postive side of the relay a fat chuncky earth wire off the earth side of the relay down to the engine then off to the starter relay wire+ side to the...

Answer:

Starter relay: Ok,,,lets try it this way and see if it's more clear Your starter relay has a total of...

Read more

TIMMY at Yahoo! Answers Mark as irrelevant Undo

Just Added Q & A:

Find solution

For every problem there is a solution! Proved by Solucija.

  • Got an issue and looking for advice?

  • Ask Solucija to search every corner of the Web for help.

  • Get workable solutions and helpful tips in a moment.

Just ask Solucija about an issue you face and immediately get a list of ready solutions, answers and tips from other Internet users. We always provide the most suitable and complete answer to your question at the top, along with a few good alternatives below.